首页
外语
计算机
考研
公务员
职业资格
财经
工程
司法
医学
专升本
自考
实用职业技能
登录
计算机
In low - speed network ,it is usually adequate to wait for congestion to occur and then react to it by telling the source of pac
In low - speed network ,it is usually adequate to wait for congestion to occur and then react to it by telling the source of pac
admin
2009-02-15
46
问题
In low - speed network ,it is usually adequate to wait for congestion to occur and then react to it by telling the source of packets to slow down. In high - speed networks, this approach often works poorly, because in the(71)between sending the notification and notification arriving at the source, thousands of additional(72)may arrive. In ATM network , a major tool for preventing(73)is(74)control. When a host wants a new virtual(75),it must describe the traffic to be offered and the service expected.
选项
A、interval
B、time
C、slot
D、delay
答案
A
解析
interval:时间间隔
转载请注明原文地址:https://kaotiyun.com/show/a4UZ777K
本试题收录于:
数据库系统工程师上午基础知识考试题库软考中级分类
0
数据库系统工程师上午基础知识考试
软考中级
相关试题推荐
图2-1所示为发送者利用非对称加密算法向接收者传送消息的过程,图中a和b处分别是(4)。
Aprojectmanagementtechniquethatiscurrentlyinwidespreaduseisthe(71).Thepurposeofthistechniqueistodetail,inh
某省6个城中(A~F)之间的网络通信线路(每条通信线路旁标注厂其长度公里数)如图1-4所示。如果要将部分千兆通信线路改造成万兆通信线路,以提升各个城市网络之间的通信容量,则至少要改造总计(61)公里的通信线路,这种总公里数最少的改造方案共有(62)
在软件开发项目中,关键路径是项目事件网络中(66),组成关键路径的活动称为关键活动。下图中的关键路径历时(67)个时间单位。(67)
若某计算机系统是由1000个元器件构成的串联系统,且每个元器件的失效率均为10-7/h,在不考虑其他因素对可靠性的影响时,该计算机系统的平均故障间隔时间为______小时。A.1×104B.5×104C.1×105D.5×105
Softwareconfigurationmanagement(SCM)isthetaskoftrackingandcontrollingchangesinthesoftware.Configurationmanagementp
在下列网络服务中,(199)是远程登录服务,Intemet中域名与IP地址之间的翻译是由(200)来完成的。(199)
在下面的项目活动网络图中,关键路径的时长为(137)周。
配置管理中有一项工作是变更控制,其中配置状态的过程如下图所示。在这个状态变化过程中,图中的(1)、(2)、(3)三个状态依次为(318)。
随机试题
A、Financialburden.B、Tastingtherurallife.C、Pursuitofherdream.D、Followingtrend.A
下述哪项是婴儿禁用药物
A.神经源肿瘤B.淋巴肉瘤C.气管支气管囊肿D.畸胎瘤E.皮样囊肿位于前纵隔心底部大血管前的囊肿
关于常用国内外文献的英文缩写A、CPAB、CAC、BAD、IPAE、EM《化学文摘》的英文缩写是
纳税评估的主要工作内容包括( )。
下列说法中符合精神分析的适应观点的是()。
下列有关人体消化系统的描述,不正确的是()。
一个测验能测出它所要测量的属性或特点的程度,称为测量的()。
在Excel2007中,选取若干个连续单元格,最简捷的方法为()。
窗体上有一个名称为Cb1的组合框,程序运行后,为了输出选中的列表项,应使用的语句是()。
最新回复
(
0
)